MECHCAD 2026
Real MECHCAD part and assembly files, ready to edit and build on. Every 2D sketch is fully dimensioned and constrained, and the assemblies have real mates. Sign in with a real e-mail to download.
Files are .metpkg packages for MECHCAD 2026. Designed by the MET Dev team as examples, not as production drawings.
100 L receiver with dished heads and weld seams, V-twin pump with crank, rods and pistons, finned 3 kW motor, belt guard, copper delivery lines and a pressure control set - every part a MECHCAD feature tree.
82 parts · 169 instances
Two 4 m runways on two-tier scissors, lift cylinders, safety racks with pawls, turntables, tread plate, hinged ramps and a hydraulic power unit - sub-assemblies joined with revolute and slider mates.
48 parts · 190 instances
Twin-arbor headstock holding a vented disc and a finned drum, saddle and cross slide on ground ways, twin cutter fork, boring bar, hand wheels with graduated dials and a welded cabinet base.
57 parts · 118 instances
Two-tier scissor on a welded frame, hydraulic ram with foot pump and release lever, safety support bar, ribbed deck mat and swivel casters with brakes.
39 parts · 116 instances
Doors on hinge mates, glass shelves, sliding crisper and deli drawers, door bins, ice maker and dispenser, plus the rear cooling circuit with compressor, condenser coil and fan.
73 parts · 139 instances
3U rack chassis: bent base tray, louvred top cover lifted to show the PCB, PSU, fan and transformer, front panel with handles.
24 parts · 55 instances
Spring-balanced parallelogram arms with real helix springs, knurled tension knobs, pivot axles with cap nuts, a turned shade with vent holes and a bent power cable.
30 parts · 50 instances
Bent-sheet side frames, crowned drive drum with shaft-mounted gear motor, tail take-up, return idlers, guides and cartons.
35 parts · 90 instances
Two-stage spur gearbox with bearings, seals and lid, V-belt drive from a motor on slide rails, all on a fabricated channel base.
49 parts · 151 instances
Housing with stainless chamber and gasket, fixed-angle 12-place rotor with bored tube pockets, colour-capped 15 ml tubes, control panel with display and buttons, hinged lid with window and gas struts.
24 parts · 70 instances
Rolled spiral scroll from one bent sheet, flanged side plates, inlet bell and guard, discharge duct with bolted flange, belt-driven.
26 parts · 55 instances
C-arm stand with coaxial coarse/fine focus knobs, mechanical stage with slide clip, Abbe condenser with iris lever, revolving nosepiece with four colour-banded objectives and a binocular head.
34 parts · 39 instances
Clamshell housing halves split on the parting line, soft-touch grip overmold, 20-step torque collar, keyless chuck and a fluted twist drill swept along a helix.
20 parts · 30 instances
Mid-tower workstation shown with the side panel removed: motherboard on brass standoffs with CPU socket, DDR5 modules, VRM heatsinks and PCIe slots, a tower CPU cooler with copper heat pipes, fin stack and fan, a triple-fan graphics card, PSU under a vented shroud, pitched-blade case fans and routed power cables.
53 parts · 120 instances
Raked rear legs, tapered front legs with wedged through tenons, filleted seat, shaped front apron, pegged stretchers and a curved back with crest rail, lower rail and three splats.
14 parts · 27 instances
Walnut case sides through-dovetailed into a cherry top, cornice and bracket-foot plinth, four graduated drawers with half-blind dovetails, pegged runners, turned knobs and brass escutcheons - one drawer pulled out.
29 parts · 48 instances
Tool changer, V-bracket carrying two parallel grippers, valve terminal with push-in fittings, sensors and cable sleeves.
23 parts · 70 instances
Desk-clamp pole with screw spindle and pressure pad, dual pivot hub and height stop collar, two parallelogram arms counterbalanced by gas springs (cylinder and rod), swivel and tilt heads with tension knobs, VESA plates carrying two thin monitors, and cables routed through pole clips.
44 parts · 94 instances
Grooved rope drum on flange bearings, shaft-mounted gear unit with brake motor, disc brake, wire rope and HEB base frame.
29 parts · 67 instances
Hi-lo parallelogram lift driven by two linear actuators on a central-locking castor base, four-section articulated deck with back-rest and knee-break actuators, split side rails on swing links, head and foot boards, IV pole socket and a wired hand control.
52 parts · 164 instances
German equatorial mount set to 40 degrees latitude, RA/DEC housings with engraved setting circles, counterweights, dovetail saddle, refractor tube with dew shield, focuser, diagonal and finder on an extendable tripod.
41 parts · 63 instances
Five-star cast base with twin-wheel casters, class-4 gas lift under a three-stage telescopic cover, synchro-tilt mechanism with tension knob and paddle levers, contoured seat, reclined mesh back with sliding lumbar pad, headrest and height-adjustable armrests.
36 parts · 73 instances
Brushed body with vented sides, cup-warmer grate, bent-tube gallery rail and steam wands, group head with portafilter, pressure gauge with 28 tick marks and a slotted drip tray.
32 parts · 55 instances
Bent panels, 16-fold frame posts, louvred doors, gland plate and a fully populated mounting plate with ducts, DIN rails and devices.
33 parts · 285 instances
Flip-top training table with an edge-banded top on pivoting channel rails, T-leg columns with head brackets, shoulder-bolt pivots, gas struts and a red release latch with paddle lever, braked twin-cheek casters, a perforated modesty panel and an open cable flap over a trough with power and data module.
36 parts · 100 instances
Three-axis Cartesian gantry built from linear actuators on an 80x80 frame, vacuum gripper, drag chains, trays and control box.
42 parts · 238 instances
Dual three-stage telescopic columns with guide collars, a motor and gearbox at each leg top, steel C-channel frame with cross beam, feet with screw levelers, laminate top with edge band and grommet, plus a perforated cable tray, cable spine and a gas-spring monitor arm on an edge clamp.
56 parts · 129 instances
Mould base for a computer-mouse shell shown open: clamp plates, A/B plates with core and cavity inserts, interlocks, guide pillars and bushes, ejector and return pins, sprue bushing, locating ring, cooling nipples and the ejected part.
22 parts · 56 instances
Block, crankshaft, rods, pistons, twin camshafts, valve train, timing drive, intake and exhaust - a complete engine assembly.
32 parts · 119 instances
Laminated maple top with 14 dog holes and tool tray, through-tenoned legs with walnut wedges, drawbored stretchers, slatted shelf, leg vise with parallel guide, tail vise, holdfast, jack plane and mallet.
32 parts · 53 instances
Solid-wood loft bed with posts and rails joined by bed bolts and barrel nuts, cleat-supported slatted base, guard rails with balusters, an angled ladder with dowel rungs, and a desk with drawer on wooden runners plus a bookshelf underneath.
45 parts · 149 instances
Profile frame with perforated sheet panels, polycarbonate windows, hinged doors with interlock, kick plates and a guarded drive inside.
71 parts · 206 instances
Oleo-pneumatic strut with trunnion, chrome piston, scissor torque links, folding drag brace with lock springs, retraction actuator, twin wheels with tie bolts, carbon brake stacks and brake lines.
35 parts · 118 instances
Cast bed with lightened girder, lagged cylinder with bolted covers, steam chest, crosshead on slide bars, connecting rod with big-end cap, counterweighted crank, six-spoke flywheel, eccentric valve gear and Watt governor.
44 parts · 112 instances
Base and wall carcasses with shaker doors on concealed cup hinges, a three-drawer stack on ball-bearing slides with one drawer pulled out, adjustable legs and plinth, a stone countertop with stainless sink, drain trap, faucet and braided supply hoses, plus a glass-door wall unit and subway-tile splash.
60 parts · 226 instances
Cast six-Y-spoke wheel, 120/70 tyre with directional tread, twin drilled floating discs on buttons, radial 4-piston calipers with pads and an inverted fork with pinch bolts.
23 parts · 73 instances
Projector shown with its top cover removed: zoom lens barrel with knurled zoom and focus rings over four glass elements, lamp cartridge with elliptical reflector and quartz burner, color wheel on its motor, light tunnel and TIR prism feeding the DMD board, finned heat sink with copper heat pipes to a fin stack, centrifugal blower, twin axial exhaust fans, PSU board and an adjustable elevator foot.
51 parts · 80 instances
Revolved bronze barrel with reinforce rings, trunnions, dolphins and touch-hole boss, stepped carriage cheeks with bolts, axletrees, iron-banded trucks, quoin, capsquares, breeching rope and a shot rack.
27 parts · 77 instances
HEA steel rack carrying process lines on shoes, cable ladder, flanged gate and ball valves, caged ladder and access platform.
64 parts · 617 instances
Reclining seat built around a pair of riveted multi-bar recliner linkages: four-bar seat links, a reclined back bracket and a two-stage lazy-tong footrest driven by a motorised linear actuator, with sinuous springs and cut-away cushions revealing the mechanism.
57 parts · 130 instances
Aluminium-profile roller conveyor with gear motor, guide rails, photo-eyes with reflectors, end stop and cartons.
20 parts · 74 instances
Finned barrels and heads, pushrod tubes, ignition harness, nose case and propeller hub - every part a parametric MECHCAD feature tree.
32 parts · 401 instances
Complete bike with 73-degree frame geometry, curved fork blades, drop bar, 2-cross laced wheels (48 spokes), 50T/34T chainrings, 11-28 cassette and a fully linked roller chain.
71 parts · 492 instances
Cam indexer with 8-station dial plate, nests and parts, stationary tooling plate with three press units, on a panelled machine base.
33 parts · 112 instances
SCARA arm with ball-screw spline and vacuum tool on an aluminium-profile table with parts tray, press fixture and light curtains.
36 parts · 95 instances
Channel, shell and bonnet joined by 24-bolt body flanges, nozzles with reinforcing pads, saddles on plinths and lifting lugs.
23 parts · 372 instances
One tracker row of twelve framed PV modules on omega rails and U-bolts, turned on a square torque tube through polymer-bushed bearing housings by a centre worm slew drive with gear motor, steadied by wind dampers on driven W-section piles and run by a self-powered controller.
36 parts · 203 instances
Generic 6-axis arm on a welded pedestal with servo joints, balancer and dress pack, picking cartons with a vacuum tool from a roller infeed onto a pallet.
60 parts · 180 instances
Pierced brass plates on turned pillars, 96-tooth great wheel with spring barrel and click, centre and third wheels with crossings, steel pinions, 30-tooth escape wheel, anchor pallets, pendulum and a chapter ring with blued hands.
38 parts · 56 instances
Three-drawer steel pedestal on full-extension ball-bearing slides (outer rail, inner rail, ball cage and balls), shown with a side cut-away and the file drawer pulled out with hanging rails and folders, central lock cylinder with key driving a cam onto a vertical locking bar, bar pulls and five swivel casters.
29 parts · 184 instances
Ventilated 330 mm disc with 36 vanes and cross drilling, 6-piston monoblock caliper, cast knuckle, tubular wishbones with bushings, coilover with real helix spring, tie rod and CV boots.
42 parts · 69 instances
Top of a hammerhead tower crane: pinned lattice mast section, geared slewing ring turned by three slewing drives with planetary gearboxes, rotating turntable with operator cab, lattice cat-head with pendant bars, jib and counter-jib root sections, trolley with sheaves and a four-fall hook block, hoist winch with rope-wound drum and stacked counterweight blocks.
60 parts · 197 instances
Duty/standby pumps with volute casings, couplings and guards, suction and discharge headers, check and gate valves, gauges.
54 parts · 287 instances
Dished-head vessel on pipe legs with nozzles, manway and davit, level gauge, roof platform with handrails and a caged ladder.
41 parts · 290 instances
Revolved spring-steel headband with cushion, graduated slider arms, rotating yokes on pivot pins, elliptical ear cups with grille slots, trim rings and lofted ear pads.
13 parts · 26 instances
Three-point-hitch seed drill with top-link mast, 900 L hopper over fluted metering units on a hex shaft driven by a ground wheel through roller chain and sprockets, swept seed tubes to six parallel-linkage row units with down-force springs, double-disc openers, gauge wheels, press wheels and folded row markers.
35 parts · 210 instances
Geared wind turbine drivetrain: cast hub with three geared pitch bearings and pitch drives, main shaft on two main bearings, a three-stage gearbox opened up to show the planetary and parallel gear stages, brake disc with calipers, flexible coupling and generator, all on a cast bedplate turned by six yaw drives on a toothed yaw ring.
60 parts · 126 instances
Floor-standing 40 L mixer with a cut-away planetary gearhead (sun gear, two planets and an internal ring gear) driving an orbiting wire whisk, handwheel bowl lift on guide rails, stainless bowl with locating pins, wire safety guard, top-mounted motor and a control panel with emergency stop.
45 parts · 75 instances
Lofted hull through eight stations with copper sheathing, planked deck, gunwale and wale strakes, 12 carronades with port lids, three masts with tops and yards, shrouds, stays and deadeyes on a display stand.
57 parts · 177 instances
Twin hexagon cutter shafts carrying forty interleaved hook-tooth discs and spacers, stripper combs, a synchronising gear pair driven through a compound reduction gear by the motor pinion, side frames in bronze bushings, feed throat, cut-away head housing and a windowed bin on swivel casters.
41 parts · 122 instances
Pouch laminator with its cover cut away: two pairs of silicone heated rollers on steel cores with heater cartridges, spring-loaded upper bearing blocks, roller gears synchronised through a compound idler and motor pinion, thermistor leaf springs on a sensor bridge, side frames, feed and exit trays with a pouch in the nip, temperature dial and controls.
39 parts · 77 instances
Laser printer-copier with the side cover removed, front door open and scanner lid raised: two paper cassettes with paper stacks, lift plates and guides, pickup, registration, transfer and exit rollers on shafts, toner cartridge with OPC drum under the laser scanner unit, fuser heat and pressure rollers, the main drive gear train on the side frame, flatbed platen with scan carriage on a belt drive, document feeder on the lid and a control panel with screen and keys.
60 parts · 114 instances
